The second method is by far the best way, especially if you are using the switch to control more than one light outlet.
Question, i want to re-wire the new light to go on the switch with the dimmer.
Instructions and wiring diagram showing the steps for wiring a light switch in your home.
Want to install a ceiling fan/ light using the existing switch that controls a table lamp.
The white joins together with the wire to each light feed and the black from each light return joins to the corresponding switch remaing screw.
Were upgrading our storage lighting from two lights, one on switch,one pullstring to two on switch and five on pullstrings.
Id like to start at the j-box w/ light, but im not sure how to make the connection from there to the 1st fluorescent fixture.
Connect the black wire from the power source to one switch terminal and connect the other switch terminal to the black wire going to the load.
Your power feed cable in to the switch outlet box first, then run a cable from the switch box up to your light outlet box.
Electrical light switch wiring basics
To my switch terminology page where i discuss the terms used for the different types of home electrical switches.
Easiest wiring of a light switch you can do is with a single-pole standard light switch.
The old one has 2 black wired and one red wire coming out of the back of the switch.
Want to thank you so much for the detailed awesome info that you give for wiring a light switch.
You need a wire with black, white, red, and ground wires to run a light switch or just black, white, and ground?
Wiring a 2-way switch is about as simple as it gets when it comes to basic house wiring.
Original switch would be the master to the outlet and the switch from the outlet and would control the light out doors.
Wires in den from wall on left side one marked to line on right, the other not marked, but guessing it is from the switch.
Have a wire comming from they light in the next room i want to know can i install a switch from that to a light?
Electrical light switch wiring diagram
Have a new ceiling lamp i took the old one down and i forgot how it was connected by the wires it is connected to a jump wire which is connected to a dimmer switch i need to know where to connect the 2 lamp wires and the jump wire.
Have a two wire black white and ground,from service to a light and then to the switch how do i wire another light in between the switch and light.
The light box, splice the black power wire in, to the white wire going to the switch.
Ground wires (bare copper) are all now connected (incoming ground, load ground and switch ground).
In your case, you have wired your light improperly, giving it power without going through you switch first.
Have a 3 way switch for my outside house lights (1 in garage 1 in house) i want to make on a timer switch (garage) is this possible?
I wired the outlet from the first light but it only works when the switch and lights are on.
When i disconnected the old fan/light, it left me with 5 wires plus a ground wire.
. 3 way switches are for large rooms or hallways where there are two (2) switches that run the same light.
Electrical light switch wiring
The light in the bathroom is now on and also the socket but i had to disconnect the wires from the light switch so the trip would stay on!
The switch box, splice the incoming neutral or white wire to the white wire going to the light box.
How do i wire this as it appears i have power into the light and into the switch?
You have an incoming hot wire (black) going to one screw (it does not matter if you use the brass or silver screw) on the side of the 2-way switch and a black wire from the other screw on the 2-way switch going to the load (light, ceiling fan etc.
Changed the switch but when i flick the fuse on one light works normally and the other light stays on permanently and cant be turned off by the switch how do i fix this problem?
Entry was posted in indoor wiring diagrams and tagged diagram, do-it-yourself, handyman, handywoman, home improvement, home renovations, home wiring, house wiring, light, light switch, power, switch, wiring, wiring diagram.
Have an outdoors light that i would like to control with two switches, let me explain.
Have two lamps it is controlled in one location (spst switch) if the switch is off, lamp one is light on but if i turn on the switch lamp one is light off while lamp two is light on.
A 15 amp breaker you can run about 18 100watt light bulbs or 1800 watts total or 120 watts per amp (breaker rating)on 120v.
Notice the black wire is the only wire that we are controlling through the 2-way switch.
When i touch one of the wires to the metal box, the light comes on.
When i turned the power back on the ceiling fixture went on but the switch wouldnt turn it off.
When i disconnected the original light, this insulated black wire had a small white lead wire that connectedthe insulated black wire to the white wire.
Can i run a wire from that switch to another light and how do i do it?
Splice them in to the wires entering the switch be for they are connected to the switch.
Have 3 recepticals on the same wire and i want to add a light switch the the middle receptical.
When i also replaced the switch on the wall i used a single pole switch.
Entry was posted in indoor wiring and tagged box, cable, diy home electrical, diy wiring, do-it-yourself wiring, home electrical, home electrical wiring, home electrical wiring diagram, home wiring, house wiring, household wiring diagram, how to wire a light switch, light switch, light switch wiring, outlet, single pole, switch, switch leg drop, wire a light switch, wiring, wiring a light switch, wiring a switch, wiring diagram.
Pagelegal-disclaimersite mapadd/see comments2-way switch3-way switch4-way switchdimmer switchoutlet/receptacleceiling fansgarden lightsthermostatsdryer cordsdryer outlettrailerscomputersrelayshome theaterdiy storesrelated linksfind an electricianlink to usabout sbiabout mecontact me.
By motion sensitive device you mean motion sensitive switch then yes, you can install it in your switch box.
Have a switch box which controls an outlet across the room, i would like to run from the out et a line to the outdoor light, between the outdoor light and the outlet i would like to add another switch to control the outdoor light.
Are two methods for wiring a basic on/off (single-pole standard duty) switch to a light or a set of lights.
What type switch do i purchase and what would be the wiring diagram for this set-up?
Inside the box that holds the light there are two white wires that are capped separately, two black wires that are entwined and capped together.
Now that you have a basic concept of wiring a 2-way switch, let's look at the following 2-way switch diagrams to see which type of circuit scenario you have.
"if you're looking for a good reference to help you understand simple home wiring, i personally recommend 'the basics of household wiring' dvd".
We had a total of five wires in the box: one for run of new lights, one for single new light, one from switch, one from power feed, one out to bathroom.
By wiring a 2-way switch, the circuit below shows the basic concept of electricity flow to the load.
This should give you a good basic understanding how the 2-way switch circuit works and will help you in adding or changing a 2-way switch.
The light fixture, the white wire connects to the fixture neutral (white) wires or neutral terminal, and the black wire connects to the fixture live(black) wires, or hot terminal (terminals are found on basic fixtures such as keyless lampholders).
I found that the hallway light just outside of the bathroom is connected through this switch.
The black live wire from the power cable in to one of the terminals on the single-pole switch (again, it doesnt matter if you use the top or the bottom terminal of the switch, but i prefer to use the bottom terminal for the hot wire), and then connect the black wire from the cable going to the light fixture to the other terminal of the switch.
The electricity flows from the hot wire (black) through the 2-way switch (shown in off position) and then to the light and returns through the neutral wire (white).
Have a junction box that includes the following: cieling light fixture, switch for the same and outlet.
Because it takes the place of your old switch, nothing is really different except that you dont need to reach over to turn the switch on/off with you hand.
The green screw on the 2-way switch is for the ground so all ground wires should be connected as seen below.